Home studio
Guidelines for recording multi-microphone acoustic guitar setups and checking phase alignment for best combined tone.
A practical guide for home studios detailing how to position multiple acoustic guitar mics, manage signal blends, and verify phase relationships to achieve a cohesive, vibrant guitar sound across a track or live session.
Published by
Nathan Turner
July 16, 2025 - 3 min Read
In modern home studios, capturing the full, resonant voice of an acoustic guitar often means layering more than one microphone. Start with a solid core by placing a central microphone close to the 12th fret, angled toward the soundhole but avoiding direct air puffs. Add a secondary mic at a lower height and farther from the body to pickup body resonance and room texture. Consider a third, room-oriented microphone if the space offers pleasant reflections that complement the direct signals. The choice of mic types—condenser for detail and dynamic for warmth—should align with the guitar’s tonal character and the mix’s needs. Maintain consistent input levels to prevent uneven dynamics.
Before you commit to a blend, establish a baseline by recording each mic individually at comparable levels. Listen for how each capture contributes to sustain, brightness, and body. Use a ruler-like approach: keep one microphone as the anchor, the others as complementary voices. Check for phase alignment through quick listening tests and simple phase checks: flip one mic’s polarity and listen for a fuller, louder response or a hollow cancellation. Small adjustments in distance or angle can alter perceived proximity and air. Document these starting points so you can reproduce or tweak the setup across sessions.
Fine-tuning mic blend and spacing without overcomplicating the chain.
With multiple microphones, phase coherence becomes a central concern because overlapping low and mid frequencies can cancel or reinforce unexpectedly. Begin by ensuring all mics are wired to a common ground and that cables are free of wear that might introduce hum or intermittent phase shifts. Use a reference source, like a click track or a constant tone, while recording each mic. Compare waveforms in your DAW to assess relative arrival times and the smoothness of the combined signal. Phase alignment isn’t only about polarity; it’s about aligning arrival times so that the fundamental and overtones reinforce rather than compete.
Practical phase checks involve small, repeatable movements. Shift one microphone a few centimeters forward or backward or tilt it slightly off-axis to find the spot where the blend feels most cohesive. When you can, perform a quick mono-to-stereo comparison to evaluate whether the center image holds up. A well-phased mix should retain punch when collapsed to mono, preserving articulation without losing the guitar’s body. If you hear a surprising hollow or shrill spike, revert to previous positions and test again, recording short clips to map how changes influence the tonal balance over time.
Build a balanced blend through thoughtful positioning and listening.
Once the physical positioning feels stable, translate it into gain structure and EQ decisions. Pad any hot outputs to avoid clipping while maintaining intelligibility, especially on the brighter top mic. A gentle high-shelf boost or cut can help avoid scoopiness when mics fight for presence, but be mindful of phase quirks that appear more prominently at extreme EQ. If you’re using a room mic, apply a mild low-cut to reduce bass clutter from room modes, then blend it with the close mics to preserve space without mud. Keep your monitor listening environment neutral to prevent ear fatigue during long sessions.
In a multi-mic acoustic guitar setup, monitoring strategy matters as much as mic technique. Use headphones sparingly to prevent symmetry loss in the stereo image; rely on accurate nearfield monitors to judge depth and width. Acknowledge how each mic contributes to the perceived proximity of the guitar. If the room is lively, leverage that energy by attenuating certain high-frequency content in the far mic so the room breath doesn’t overwhelm the direct tone. Conversely, a dead room can benefit from brighter mics that bring articulation to the forefront, so adjust accordingly.
Consistent checks ensure reliable phase behavior across takes.
When planning a live-feel take, consider how to preserve the dynamics of strummed passages across multiple mics. The strumming motion tends to excite a broad spectrum, so ensure the midrange doesn’t become congested by overlapping voices. Acoustic guitars often benefit from a main microphone near the fretboard for clarity and a secondary that captures body resonance near the bass side. If you record in a small room, treat reflective surfaces with absorptive panels to minimize early reflections that can muddy phase cues. Always re-check phase after changing strings or adjusting the guitar’s neck relief, as that can subtly shift the timing of spectral content.
When you’re ready to commit a take, perform a quick “collection test” by routing the mics into a single bus and evaluating the combined tone. Solo each mic briefly to hear its contribution and how phase affects the sum. Listen for any comb-filter artifacts that indicate timing misalignment; if present, fine-tune delays or reposition to restore coherence. Keep a log of settings, including distances, angles, and gains, so you can reproduce ideal results in future sessions. This discipline prevents drift and helps maintain consistency across songs and recording days.
A steady process drives consistent, high-quality results.
In addition to the technical side, don’t overlook the guitarist’s technique as a source of variable phase relationships. Subtle shifts in picking dynamics or capo placement can alter how each mic captures transients and room reflections. Encourage the player to maintain even attack and avoid aggressive textures that might exaggerate phase differences between mics. As you experiment, consider alternate guitar tunings or drop tunings that affect string tension and resonance, then re-evaluate the mic pairs. Small changes in instrument setup require corresponding adjustments in mic positioning to preserve a coherent, natural blend.
A reliable workflow includes treating the room as a partner rather than a nuisance. Use diffusers or absorbers to tame problematic frequencies without killing the ambiance that gives acoustic guitar its life. For most bedroom studios, a balanced approach—one close mic for detail, one mid-distance for body, and one room mic—offers flexibility. After you settle on a tone, run a few blind comparisons with and without the distant mic to confirm that the room’s contribution enhances rather than obscures the guitar. Blind listening helps you trust your ears beyond brand names or favorite presets.
Finally, when assembling the final stereo image, consider the pan law and how it interacts with the blend. A symmetrical stereo spread often works well for acoustic guitars, but adjust to taste if your mix has other wide elements. Phase alignment matters more as you widen the mix, so verify that the combined tone remains centered and balanced when collapsed to mono. Use a reference track with a similar acoustic guitar setup to gauge the authenticity of your tone. Regularly revisit your runaway early reflections and re-check mic aim after any substantial room change.
In sum, a thoughtful multi-mic approach to acoustic guitar requires patience, careful listening, and repeatable processes. Start with a solid core and intermediate support mics, then refine phase through precise placement and polarity checks. Track every adjustment in a careful notebook so you can reproduce or improve later. When you keep the system coherent, the final mix will reveal a natural, integrated guitar voice—not a collage of separate sounds. With discipline and curiosity, you’ll uncover a dynamic, enduring tone that suits a wide range of songs and styles.
