Stay Plugged In With Canon
Latest News & Updates

Brake noise often arises from imperfect contact between brake pad backing plates, shims, and caliper hardware. Selecting the right shim material and thickness helps adjust the clamping force distribution, reducing vibration that travels through the pad into the brake system. Common shim materials include steel, stainless steel, and copper alloys, each with distinct frictional and thermal properties. In many cases, a universal shim may suffice, but high-performance or heavy-duty applications benefit from tailored thickness and rigidity. When evaluating options, consider compatibility with your rotor finish, pad compound, and caliper design to avoid interference and uneven wear that can spawn squeal.

Anti-squeal coatings provide an additional layer of NVH control by dampening micro-movements at the pad-to-shim interface. The right coating reduces stick-slip phenomena that trigger squeal under light to moderate braking. Coatings vary in solvent resistance, curing time, and temperature tolerance, so check temperature ratings that align with your braking demands and climate. Some coatings are designed for pre-mybridization with the pad, while others are applied to the shim surface. Importantly, coating adhesion should endure repeated heat cycles without cracking or peeling. Always follow manufacturer guidance for cure times and surface preparation to maximize performance and longevity.

Start by identifying the brake system family your vehicle belongs to, such as a compact car, SUV, or performance sedan. Each category often uses distinctive pad shapes, backing plate profiles, and caliper mounting hardware that influence shim fitment. After confirming compatibility, examine pad chemistry because friction materials with differing binders and abrasives interact uniquely with shim materials. A mismatch can lead to creaking or silent but compromised braking efficiency. For vehicles with high rotor temperatures or frequent heavy braking, consider thicker shims or reinforced coatings that can maintain damping properties without adding excessive caliper clearance.

Once the baseline compatibility is established, evaluate environmental conditions and usage patterns. Vehicles operated in cold climates may experience different squeal tendencies than those in hot arid regions due to thermal cycling and moisture ingress. Similarly, frequent stop-and-go driving versus long highway cruising alters thermal load and acoustic behavior. In such cases, a multi-layer approach—combining a robust shim with a durable coating—may offer superior sustained performance. Document any noise onset patterns and correlate them with operating temperatures to guide the selection of materials that maintain braking efficacy across the expected service range.

When choosing shim material, consider rigidity versus compliance. A stiffer shim transmits less energy back into the pad, potentially reducing squeal but raising the risk of felt vibration if the caliper is misaligned. A compliant shim can absorb more energy, smoothing the interface, yet may wear faster or deform over time. Stainless steel is a common middle ground, offering corrosion resistance and predictable damping. In high-humidity environments, a copper alloy shim might provide slightly better groove tolerance, but watch for potential copper transfer to the rotor. Material selection should match the car’s weight, braking demands, and rotor geometry to preserve braking performance.

Coating selection hinges on temperature exposure and the pad’s operational envelope. High-temperature environments benefit from coatings with automotive-grade resin systems that resist breakdown under repeated heating. Application methods vary, with some coatings sprayed or brushed onto the shim edge, and others applied to the pad surface before installation. Cure time and surface preparation are crucial for adhesion. Poor preparation invites delamination, which can accelerate wear or create new squeal modes. Additionally, verify chemical compatibility with the pad binder and any moisture sealant present in the caliper area to ensure the coating remains effective through life cycles.

Before installation, clean all mating surfaces thoroughly to remove oils, cleaners, and bronze dust that may hinder adhesion. Use isopropyl alcohol or a dedicated brake cleaner and allow complete solvent evaporation. Inspect the caliper pistons and hardware for corrosion or pitting that could transfer unwanted vibration to the pad. When installing, ensure a uniform gap around the backing plate and shim to avoid edge contact that can create sporadic squeal. If the shim is too tight, the pad may not seat properly, and if too loose, clattering can occur during normal operation. Test fit with the rotor removed to confirm clearance.

After fitting, perform a controlled brake bed-in procedure to settle the new components. This usually involves a series of moderate to firm stops from moderate speeds to transfer a consistent layer of pad material to the rotor. Monitor for any immediate noise or palpitation that signals improper installation or wrong material pairing. In the first 500 miles, drive with smooth, predictable braking to avoid thermal shock. If squeak or chatter emerges, reassess shim thickness or coating integrity rather than immediately changing pad compounds, as these changes can significantly affect braking balance and pedal feel.

Regular inspection of the brake system helps catch issues before they become audible or performance-limiting. Check shim edges for deformation, coating cracking, or chipping that could alter damping behavior. Inspect the pad thickness at multiple locations to detect uneven wear that indicates improper caliper alignment or sticking hardware. If a coating is delaminating, do not attempt to recoat; replace the shim or pad assembly to restore consistent contact and noise control. Maintaining caliper slide pins, guide bolts, and anti-rattle clips keeps paralleled force across the pad, supporting quieter operation and even wear.

Longevity depends on synergy among pad, shim, coating, and rotor condition. If rotors are deeply scored or warped, even the best shim and coating may not suppress noise effectively. In such cases, rotor resurfacing or replacement can restore a clean contact surface, enabling the damping system to function as designed. Maintain a careful inventory of parts and ensure replacements are matched to the vehicle’s original specifications. Keeping a record of service intervals, materials used, and observed noise patterns helps inform future maintenance decisions and reduces the chance of recurring squeal.

When sourcing shims and coatings, prioritize OEM-compatible components or reputable aftermarket brands with documented performance data. Read supplier data sheets for material composition, thickness tolerance, coefficient of friction, and temperature resistance. A label indicating compatibility with your pad compound and rotor finish is a strong sign of reliability. Beware of generic packages that do not specify mechanical properties, as these can behave unpredictably under heat cycles. If possible, consult a qualified technician who can measure caliper gaps and confirm the chosen parts will not interfere with wheel movement or brake clearance.

Finally, consider warranty and service options. A good warranty demonstrates the manufacturer’s confidence in the product’s performance under real-world conditions. Favor coatings with reputed adhesion guarantees and shim sets that are designed for common rotor finishes and caliper geometries used on your vehicle. When in doubt, request a sample kit and perform a short, controlled test on a non-critical vehicle to verify noise suppression and braking response. With careful selection, precise installation, and attentive maintenance, you can enjoy quieter braking without sacrificing stopping power or rotor life.