Stay Plugged In With Canon
Latest News & Updates

In 3D printing, infill percentage is a key lever for controlling part behavior beyond the exterior geometry. The infill creates internal structure that supports loads, resists deformation, and contributes to weight. Higher percentages generally increase stiffness and strength, while lower percentages reduce print time and material use. However, the relationship is not simply linear, because wall thickness, material properties, and print process all interact with the chosen infill. For functional parts—such as enclosures, brackets, or housings—you need to consider the expected forces, impact scenarios, and thermal conditions. A thoughtful infill setup balances safety margins with efficiency, avoiding overbuilds that waste material and time.

Before settling on a number, identify the functional requirements of the part: load paths, fatigue expectations, and environmental exposure. Different regions of a single part may demand different performance characteristics; for example, a hinge may require more flexibility near the joint yet rigid sections elsewhere. Start with a moderate baseline—say 20–40%—and adjust incrementally based on testing results. Consider the material’s intrinsic strength and ductility as well; a high-strength polymer may deliver adequate performance at a lower infill, whereas a brittle filament might need denser internal support. Document the testing setup so future revisions follow a clear learning curve.

Infill pattern dramatically affects how loads travel through the print. Gyroid, cubic, and lattice structures distribute forces differently than a simple grid, often providing improved resistance to bending and torsion with comparable densities. For parts that endure cyclic loading, a pattern that promotes isotropic behavior can help reduce weak directions. The chosen pattern also influences print time, nozzle temperature, and cooling requirements. When optimizing for functional parts, run small prototypes that compare several patterns under representative loads. Record which pattern yields the desired balance of stiffness and compliance, along with any noticeable deflection under load. Over time, this approach reveals which patterns suit particular geometries.

Alongside the interior pattern, the shell or perimeter walls play a crucial role. Increasing wall count can significantly boost part stiffness and load-bearing capacity without a large rise in total material. If a component must flex slightly, keep the outer walls conservative and push the infill to contribute to overall rigidity elsewhere. Temperature resistance and layer adhesion also affect performance; at higher print temperatures, stronger interlayer bonding can compensate for lighter infill. Always verify that the exterior surface remains acceptable for mating with other parts, as a thick shell can obscure fine features or cause fit issues. The net effect is that shell and infill choices must be harmonized.

Setting target mechanical properties helps translate ideas into printable parameters. Start by defining acceptable ranges for stiffness, yield strength, and impact resistance based on real-use scenarios. Use standardized test coupons or representative prototypes to gather data. For example, a bracket might require a specific minimum deflection under a known load, while a cover may need to resist impact without cracking. Use these criteria to guide infill percentages and patterns. Document the test method and results, then adjust the settings to converge on a design that stays within tolerances under practical conditions. Consistency in testing ensures repeatable outcomes across batches.

Consider print orientation as a companion variable to infill. The direction of strongest layer bonding can amplify or mitigate the effect of infill density. Parts loaded in directions parallel to layer lines can behave very differently from those loaded across layers. If you cannot reorient a part, choose an infill density that compensates for anisotropy. You can also introduce gradual transitions—regions with denser infill near high-load areas and lighter infill where loads are mild. These transitions must be designed so they do not introduce stress concentrations or potential delamination during use. A cohesive strategy couples infill with orientation for robust performance.

When durability matters most, higher infill is often warranted, but not always. For functional parts exposed to bending or torsion, an infill in the 40–60% range commonly yields noticeable gains in stiffness. If weight is critical, try near-60% but couple it with a pattern optimized for strength rather than sheer bulk. For components that must absorb impact or cushion joints, a slightly lower infill can work, especially if you pair it with an elastomeric or flexible material. Testing remains essential; even well-chosen defaults can fail under unexpected conditions. Iterative testing with real-world loads builds confidence that the chosen infill strategy will endure.

Material selection can change the ideal infill percentage dramatically. A tough engineering polymer may reach required performance at surprisingly modest densities, while a brittle or low-elongation filament benefits from denser infill to distribute stress. Some materials respond excellently to specific patterns that encourage crack deflection or fiber-like behavior. Don’t assume the same percentage will work across different filaments. Instead, build a small matrix of tests across densities and patterns for each material and part geometry you intend to produce. Results from one material should not be naively extrapolated to another, even if the part shape is familiar.

For enclosure shells that protect delicate internals, moderate infill often suffices but reliability matters. A 20–40% density with a strong gyroid or cubic lattice can yield good rigidity while permitting some energy absorption. If the enclosure must withstand dropped-object tests, consider increasing density to 40–60% in critical regions or adding stiffer edge supports. Fasteners and mounting bosses benefit from thicker ribs or slightly higher infill in surrounding areas to prevent deformation. The goal is to keep the exterior smooth and functional while ensuring the internal structure stops bowing or cracking under typical impacts.

Brackets and mounts represent a class of parts where joint longevity is essential. These components demand higher infill near mounting holes or contact surfaces to resist shear and fatigue. A practical approach is to use a higher density, combined with a pattern that resists crack initiation. However, avoid uniformly maxing out infill as that increases weight and may introduce material waste. An efficient compromise allocates more material where stress concentrates, and less where there is little load. Testing under repeated cycles will reveal whether the chosen configuration maintains clearance and alignment over time.

Infill choices interact with printer calibration. Under-extrusion, temperature fluctuations, and bed adhesion issues can masquerade as poor infill performance, so ensure your printer is well-tuned before relying on results. Calibrate extrusion rates, ensure consistent cooling, and verify dimensional accuracy with test prints before committing to production parts. One useful practice is to print a small test piece for each new infill configuration, measuring deflection, weight, and failure thresholds. This preparation helps distinguish material behavior from process-related anomalies and speeds up design iterations.

Ultimately, the art of choosing infill percentages is about translating performance goals into printable strategies. Start with a conservative baseline, then explore patterns, shell thickness, and orientation to hit your targets. Document everything: material type, print settings, test results, and observed failure modes. This record becomes a valuable reference as you scale production or tackle new design challenges. With careful experimentation, you’ll achieve functional parts that meet strength and flexibility requirements while avoiding wasted material and excessive print times.